Perform a Gate Location analysis in Moldflow Insight | Autodesk
Perform a Gate Location analysis in Moldflow Insight | Autodesk
10 months ago
autodesk.com
Ever wondered why a runner looks “fine” on CAD… but Moldflow shows air traps everywhere? 🤯 In this clip, the issue is coming from two sharp runner corners 👇 🔍 What happens: * Small corner radius → turbulence/jetting → air gets trapped * The trapped air travels into the cavity → higher porosity & defect risk ✅ Quick optimization: * Increase the radii at the two key corners to smooth the flow * Recheck gate/overflow/venting around the last-to-fill area At Cast Mold, we run DFM Moldflow before c
0:07
Ever wondered why a runner looks “fine” on CAD… but Moldflow shows air traps everywhere? 🤯 In this clip, the issue is coming from two sharp runner corners 👇 🔍 What happens: * Small corner radius → turbulence/jetting → air gets trapped * The trapped air travels into the cavity → higher porosity & defect risk ✅ Quick optimization: * Increase the radii at the two key corners to smooth the flow * Recheck gate/overflow/venting around the last-to-fill area At Cast Mold, we run DFM Moldflow before c
80.6K views4 months ago
Facebook胡睿
Gate types, importance and simulation in Injection Molding
Gate types, importance and simulation in Injection Molding
Jun 10, 2021
makenica.com
Why Inclined Ejection Was Used for a Large Internal Undercut in an Automotive Mold
1:59
Why Inclined Ejection Was Used for a Large Internal Undercut in an Automotive Mold
185 views2 months ago
YouTubeMoldevo | Injection Mold Design • DFM • Moldflow
Ruby on Instagram: "10 seconds to understand the advantage of a Tangential Gate ⚙️ In this Moldflow clip, we’re showing a typical filling pattern with a tangential gate: ✅ Tangential entry guides the melt flow for a smoother, more stable filling behavior ✅ Helps avoid direct impingement, reducing die-core erosion risk ✅ A great option for ring-shaped castings, promoting a more uniform circumferential flow ⚠️ One key reminder: Venting/overflow locations must match the tangential flow direction —
0:09
Ruby on Instagram: "10 seconds to understand the advantage of a Tangential Gate ⚙️ In this Moldflow clip, we’re showing a typical filling pattern with a tangential gate: ✅ Tangential entry guides the melt flow for a smoother, more stable filling behavior ✅ Helps avoid direct impingement, reducing die-core erosion risk ✅ A great option for ring-shaped castings, promoting a more uniform circumferential flow ⚠️ One key reminder: Venting/overflow locations must match the tangential flow direction —
90.6K views5 months ago
Instagramruby_diecasting
Ruby on Instagram: "🔥 How to Choose the Best Gate Location in Die Casting? Just changing the gate position can totally change your casting result. Here’s a quick Moldflow comparison from our latest project 👇 ❌ Bad Gate Location Causes: • Turbulence → trapped air • Porosity in critical areas • Cold shuts / short shots • Harder to get a clean T1 ✅ Optimized Gate Location Gives You: • Smoother filling • Lower porosity in functional zones • More stable shots • Cleaner surface & fewer defects Gate
Ruby on Instagram: "🔥 How to Choose the Best Gate Location in Die Casting? Just changing the gate position can totally change your casting result. Here’s a quick Moldflow comparison from our latest project 👇 ❌ Bad Gate Location Causes: • Turbulence → trapped air • Porosity in critical areas • Cold shuts / short shots • Harder to get a clean T1 ✅ Optimized Gate Location Gives You: • Smoother filling • Lower porosity in functional zones • More stable shots • Cleaner surface & fewer defects Gate
57.6K views6 months ago
Instagramruby_diecasting
Plastic Processing Overview
6:09
Plastic Processing Overview
2.3M viewsAug 25, 2015
YouTubeConairGroup
17:05
Injection Molding Overview
231.6K viewsAug 31, 2015
YouTubeAutodesk Simulation
47:17
Moldflow Insight Fundamentals
55.9K viewsNov 24, 2020
YouTubeAutodesk Advanced Manufacturing
11:01
Plastic Injection Molding Simulation
109.6K viewsFeb 6, 2013
YouTubeIDSPL SOLIDWORKS
3:07
Overview - Autodesk Moldflow
91.1K viewsMay 5, 2011
YouTubeAutodesk Inventor
5:03
Modeling Runner Systems
12.1K viewsJun 10, 2016
YouTubeAutodesk Simulation
4:11
Introduction to Sequential Circuits
449.3K viewsJan 27, 2018
YouTubeTutorialsPoint
5:24
Sequence Valve - Pressure Control Valve
67.7K viewsDec 24, 2020
YouTubeBEST MECHANICAL ENGINEERING
1:13
Ultra Helix Valve Gates
29.2K viewsNov 24, 2016
YouTubeHusky Technologies™
0:28
Process Technology: Gate Valves
78.9K viewsAug 19, 2011
YouTubeCTE Skills.com
27:02
Sequence Valves (Full Lecture)
62.7K viewsMar 21, 2016
YouTubeJim Pytel
10:54
Valve Gates & How They Work
9.5K viewsDec 29, 2020
YouTubeInjection Molding Skills & More
2:27
EWIKON Hotrunner Systems - Valve Gate Technology
30.9K viewsNov 6, 2015
YouTubeEWIKON Heißkanalsysteme GmbH
8:25
Introduction to Sequential Circuits | Important
3.2M viewsFeb 1, 2015
YouTubeNeso Academy
53:13
Moldflow Advanced Results Customization
8.2K viewsNov 24, 2020
YouTubeAutodesk Advanced Manufacturing
5:05
Sequence Valve Schematic Simulation
37.6K viewsOct 7, 2020
YouTubeKletteTech
19:44
MoldFlow Adviser tutorial: Single cavity analysis
83K viewsMay 20, 2015
YouTubeKlaus Falk
11:25
Intro to Markov Chains & Transition Diagrams
176.2K viewsSep 7, 2020
YouTubeDr. Trefor Bazett
1:52
Two-shot sequential overmolding
2.7K viewsSep 21, 2015
YouTubeAutodesk Moldflow
2:05
Types of Gating for Injection Molding
1.9K viewsMay 13, 2021
YouTubeKenny Han
1:03
OverTEC -- Techsil's New Low Pressure Injection Moulding Technology
68.3K viewsJul 16, 2013
YouTubeTECHSiL
3:37
Plastic Injection Molding: 9 Injection Gate Types
10K viewsMay 2, 2019
YouTubeSofeast
3:03
ANNTONG - Single Valve Gate(SVG) Hot Runner System
16.8K viewsApr 8, 2016
YouTube映通（映通股份有限公司）
3:19
The Technology of Injection Molding Training with 3-D Animations
662.3K viewsJun 20, 2017
YouTubePaulsonTraining
See more
Static thumbnail place holder